125mm Electronic Disc Grinder G13VE2

Electronic Disc Grinder:G13VE2

  • Double Insulation
  • Brushless motor

High Power

Max Output 1,900W

Max Output

Max output increased by approx. 10% compared with conventional products.

Overload Capacity*

Overload capacity increased by 1.4 times.
  • The values shown are for reference purposes and may vary according to the workpiece materials and other operating conditions.

Durability to Withstand Rough Jobsite Conditions

Heavy-Duty Motor

The motor redesigned with new components allows increased durability.

Long Lasting Controller with Four Times* More Dust Resistance

The electronic controller is insulated and protected against metallic dust.

  • Vs. HiKOKI's G10VE disc grinder. The value shown is for reference purposes and may vary according to the workpiece materials and other operating conditions.

Dust Resistant Filter

The fine mesh filter of the air inlet drastically increases the dust resistance.

Standard Accessory
Fine Mesh Dust Filter

56mm Grip Dia.
Filter position

Maintenance-Free and Highly Efficient AC Brushless Motor

Longer Lifetime*1

The AC brushless motor offers a significantly extended product life cycle by eliminating trouble including armature burnout, layer short or commutator wear even in severe work environments.

Maintenance-Free

No carbon brush replacement is required, which saves time and cost.

Stable Operation during Voltage Drop

The performance isn't affected as much by voltage drop from long extension cords on site. This vastly improves electrical efficiency.

The motor runs cooler and Very little performance degradation when used with an extension cord.

Excellent Grinding Performance with Less Fluctuation in Speed*1

The highly efficient AC brushless motor and electronic speed control maintains the speed and ensures work efficiency even when the load increases.

  1. Compared with HiKOKI brushed disc grinders.
  2. Use an extension cord no longer than 50m.

Ergonomic Design

  • Small Grip Circumference

    For more comfort and control

    56mm Grip Dia.
  • 'Continue To Run' Function*

    Even after the motor has stopped due to overloading, it gets activated automatically if the load decreases within 1.5 seconds, so users do not have to restart the tool manually.

    'Continue To Run' Function
    • The motor may not automatically restart when the kick-back protection is activated or for other safety reasons. In that case, the tool needs to be turned off and on manually.
  • Variable Speed Control

    The rotation speed can be adjusted with a dial between 2,500/min and 8,500/min according to the application.

    Dial Settings and No Load Speeds

    Dial No Load Speed
    (/min)
    Use
    1 2,500 Polishing, Finishing
    2 3,200 Polishing, Finishing
    Removal of Paint or Coat, Removal of Rust, Removal of Burrs
    3 4,700 Removal of Paint or Coat, Removal of Rust, Removal of Burrs
    4 6,400 Removal of Paint or Coat, Removal of Rust, Removal of Burrs
    5 7,700 Grinding
    6 8,500 Rough Grinding, Cutting
  • 3 Position Side Handle

    Fitting the side handle on top of the tool allows for easy operation in tight spaces.

    3 Position Side Handle
  • Tool-less Wheel Guard

    The wheel guard can be installed or adjusted just by pulling the quick release lever.

    Tool-less Wheel Guard
  • Easy to Use Switch

    The stepped design of the power switch makes it easy to operate.

    Easy to Use Switch

Great Safety Features

  • Kickback Protection System

    Monitors a sudden drop in the motor rotation speed and stops the motor quickly to reduce the reaction force (kickback).

    Depending on operating conditions, the Kickback Protection System may not work or provide specified performance. Make sure that the workpiece is placed and supported properly, and that the main unit is held firmly during operation. Additionally, carefully read "KICKBACK AND RELATED WARNINGS" in the instruction manual.
  • Restart Protection

    The motor does not restart after the power has been temporarily cut off during operation to avoid accidents.

  • Soft Start

    Allows comfortable operation by reducing the reaction force on start up.

Specifications

Capacity Wheel Dia. 125mm
Hole Dia. 22.23mm
Thickness 6mm
Spindle Thread M14 x 2
Power Input 1,320W
Max Power Output 1,900W
No Load Speed 2,500 - 8,500/min
Overall Length 323mm
Weight*1 2.4kg
Standard Accessories*2 Wheel Guard, Side Handle, Guard Clip, Wrench
  1. Weight: according to EPTA-Procedure 01/2014.
  2. Standard accessories vary by country or area.
PDF: 1,599KB
  • Please contact local dealers for product availability and product details.